Test des tâches

  Test des rayures

  Test de l’abrasion

  Test UV

  Test d’ébullition

UltraShield a montré une absence de tache, après lavage, contrairement au composite conventionnel.
  •  
  •  
  •  
  •  

UltraShield : à 20N aucune marque apparente
Composite classique : à 8N des marques apparaissent

● En utilisant une seringue de 1 mm pour marquer le composite
 ● Test réalisé sous une pression de 8N-20N
● Test standard utilisé : FLTM BO 162-01
  •  
  •  
  •  
Après 1000 tours 23mg du matériau d’UltraShield disparait
Après 1000 tours 81mg du matériau classique disparait
  •  
  •  
Testé dans une chambre QUV pendant 3000 heures.
Les experts concluent qu’aucune trace visible ne peut être observée avec un delta E<5,0.

 ● Les observations et les enregistrements sont effectués toutes les 500 heures
  •  
  •  
  •  
  •  
  •  
  •  
Les photos ci-dessous montrent l’UltraShield après 90 heures du test d’ébullition.
Les résultats ne montrent aucune séparation entre la couche de protection et la partie centrale, aucun dommage et aucun craquement
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
 

UltraShield® vs. Conventional Decking

Test 1: Stains

  • Step 1
    Stain with black ink

UltraShield® Decking

ultrashield test 1

Conventional Decking

ultrashield test 2
  • Step 2
    Wipe out half of the ink
ultrashield test 3
ultrashield test 4
  • Step 3
    Wash off by water
ultrashield test 5
ultrashield test 6
  • Last Step
    Dry and see the result

No penetration through the top layer and no stain left

ultrashield test 7

Stain remains

ultrashield test 8

Test 2: Scratches

  • Use 1mm needle
  • Test scratch damage under 8N-20N pressure
  • Test Standard: FLTM BO 162-01
ultrashield test 1

UltraShield® Decking

ultrashield test 1

Conventional Decking

ultrashield test 2

UltraShield® 20N: No obvious mark

ultrashield test 3

Conventional 8N: Mark appears

ultrashield test 4

UltraShield® 20N: No obvious mark

ultrashield test 5

Conventional 8N: Mark appears

ultrashield test 6

Test 3: Abrasions

  • Testing: 750g Weight, 60 turn/min, 1000 turns
  • Test Standard: ASTM D4060
ultrashield test 1
  • Original

UltraShield®

ultrashield abrasion 1

Conventional composite wood

ultrashield abrasion 1
  • Scratch mark and the wore off powder weight after test

UltraShield® 23mg

ultrashield abrasion 1

Conventional composite wood 81mg

ultrashield abrasion 1

Test 4: UV

  • QUV chamber test up to 3000 hours
  • Observation & record in every 500 hours

UltraShield® 500 hrs: Delta E: 0.65 -1.25

ultrashield uv test

UltraShield® 1000 hrs: Delta E: 0.92 -1.41

ultrashield uv test

UltraShield® 1500 hrs: Delta E: 1.45 -1.63

ultrashield uv test

UltraShield® 2000 hrs: Delta E: 2.55 –3.54

ultrashield uv test

UltraShield® 2500 hrs: Delta E: 2.72 -3.63

ultrashield uv test

UltraShield® 3000 hrs: Delta E: 2.72 –3.75

ultrashield uv test

Summary:

Tested in a QUV chamber for 3000 hours, experts say no visible color change can be observed at a Delta E < 5.0

ultrashield uv test

Test 5: Boiling

  • Step 1:
    Put the test samples in the container (the water level needs to over the samples by at least 5 mm or more
  • Step 2:
    Turn on the heating plate to 100 degrees Celsius and record/observe every 2 hours
  • Step 3:
    Samples need to be taken out every day and the duration should be recorded. The duration is recorded after the temperature of the hot plate reaches 100 degrees Celsius
  • Step 4:
    Repeat procedure 1-3 on the second day

Boil the board up to 80 hours or more

ultrashield boiling process
ultrashield boiling process
ultrashield boiling process

Pictures below show UltraShield after a 90 hour boiling test. The results show no separation between the cap layer and the core, no damage, and no cracking

ultrashield boiling
ultrashield boiling
ultrashield boiling

 

PRODUITS

SUPPORT

NEWTECHWOOD

CONNECT

LANGUAGE

COPYRIGHT 2004-2019 NEWTECHWOOD. TOUS DROITS RESERVÉS.